Home > Accessories > Bike Transport > Buzz rack Buzzybee 2 CarRack
	Our Price: €269.95 Product Code: BZBE2 Qty:

Description Technical Specs   BUZZYBEE series offer convenient mounting, basic functions and compact storage. The rubber pad offers a good solution for carbon frames fitting as it does not apply pressure to the carbon tubes. Carrying bikes The wheel holders will accommodate most wheelbases, even small childrens bikes. You can reverse the wheel supports for the really small bikes. See technical data below The long wheel rubber-padded wheel straps hold tyres up to 3.25 wide; pull on them to tighten, and use the quick release to loosen The BUZZYBEE 2 is entirely suitable for carbon frame bikes; the rubber bike frame pads and high resistance straps hold any type of tube firmly but gently. The maximum permitted load is 40kg, with no bike weighing more than 20kg The down tube size is limited to 75mm diameter (3); whatever bikes you have, always load the heaviest bikes nearest to the car Other features and basic specifications The patented conical fitting fits to all tow balls, even to the bolt-on tow balls we see occasionally that do not meet standards for neck length or ball diameter. A reminder that it locks to the tow ball. The BUZZYBEE 2 sits high on the tow ball, well clear of speed bumps and other hazards such as steep ferry ramps. Dimensions: 88cm wide x 52cm deep (measured from the centre of the tow ball to the outside edge of the number plate holder). Weight: 8.5kg The build quality tube bending, welding, rust proofing, painting, component quality, is exemplary. The whole carrier looks and feels like the class act it is. All tools you might need are provided. All parts are replaceable if e.g. someone forgets that a tow bar carrier is fitted and reverses into a wall which happens! Not suitable for trailers, campers, or RVs Features Basic ergonomics The BUZZYBEE 2 is very compact and light with a weight of 8.5kg! Very compact geometry but fits most bike sizes! Key features of the BUZZYBEE 2 Assembly: Even though it is not assembled, BUZZYBEE 2 is very easy to put together: assemble the wheel support frame to the base using 4 screws, assemble the light support with 2 more screws, install the license plate, slide in the plastic wheel supports, fit the rack to the tow ball with no tools needed and you are ready to go! Fitting to the car: When you first place the BUZZYBEE 2 on the tow ball it supports itself you can let go of it and it wont fall to the ground. Youll then take the weight again, spin the tightening knob until its tight, and lock it. BUZZRACKs carriers comply with the very exacting standard XPR-18-904-4 and therefore include an anti-sway tensioner; this has an integrated handle and 2 or 3 turns are usually sufficient. The video below shows the fitting to the car and the installation of bikes. Lighting system: The BUZZYBEE 2 comes with a 7 pin lighting system. 7 pin to 13 pin adapter is not included but can be purchased as an option. (3 function 7 pin flat plug for AUS/NZ)

Related Products... Rapid Fitting Kit Our Price: €42.99 Add 6060 Evo Flush Rail fitting kit Our Price: €49.99 Add 52417 Bike Arm Long 482 mm w/o Lock Our Price: €64.99 Add Fixpoint Fitting Kit Our Price: €49.99 Add 760 SquareBar 108 cm roof bars Our Price: €74.99 Add

Browse for more products in the same category as this item: Accessories > Bike Transport Accessories

Product price is not filled in. This product cannot be purchased.

Product price is not filled in. This product cannot be purchased.

Product price is not filled in. This product cannot be purchased.

Product price is not filled in. This product cannot be purchased.

Product price is not filled in. This product cannot be purchased.

	XT RD-M8000 11-speed rear derailleur €99.99
	RX Prescription Insert - Mission II €5.99
	609 2RS - ABEC 3 €5.49
	HeadSet Electra Townie 1-1/8in Zero Stack Threaded Silver €35.00